Zeitronix ZT-2 plus ZR-1 AFR / Lambda Gauge Blue LED Digits Black Bezel
Zeitronix ZT-2 plus ZR-1 AFR / Lambda Gauge Blue LED Digits Black Bezel
Zt-2 wideband with the ZR-1 Gauge which displays Air/Fuel ratio or Lambda values and has a peak and hold feature. High contrast LEDs are visible even in a direct sunlight.
Zeitronix Zt-2 + ZR-1 Air/Fuel Gauge Bundle Blue LED Digits Black Bezel
Includes:
- Zeitronix Wideband Zt-2 Air/Fuel ratio meter and datalogging system 2010 and up model
- Zeitronix Wideband ZR-1 3-Digit Wideband Air/Fuel and Lambda Gauge with Black bezel and Blue Text
- BONUS - Includes USB to Serial Port Adapter - we are the only retailer including this necessary cable!
We are an official Zeitronix Distributor and we have the new models in stock. There ARE differences between the new and older models.
Includes the Zt-2 Wideband Air/Fuel Ratio Meter, Wideband Oxygen Sensor, Sensor Harness, Signal Harness, PC Serial Cable, Datalogging Software, Installation Instructions and 2-Pin EGT Connector to retrofit your EGT probe. Data splitter included for simultaneous display and datalogging use. Made in the USA.
The Zeitronix Wideband Air/Fuel ratio meter and datalogging system is a high quality, stand-alone system for use with carbureted and electronic fuel injection engines. Zt-2 Wideband Kits provide the best bang for your buck delivering unmatched quality, features and capabilities for very reasonable prices. The Zeitronix system provides the accuracy of a Dyno Air/Fuel reading right in your vehicle as well as multiple engine parameters. Supports Air/Fuel ratio as AFR/Lambda, plus RPM, Vacuum, Boost, Exhaust Gas Temperature, Throttle Position, 0-5 volt sensors, and Air/Fluid temperature sensors. Tune fuel injected and carbureted engines. Very simple installation. Connect two wires to +12V and ground and place the O2 sensor in the exhaust stream and you are ready to read AFR! Cut your tuning time in half!
Finally you can tune for more power, closer to the edge, precisely monitoring Air/Fuel ratio Boost, EGT, RPM and throttle position datalogging up to 9 hours of data with a blazing rate of 74 samples per seconds per graph. The ZDL software can be utilized as a real time display when using a basic Zt-2 kit without the hardware display. Fully digital, smallest wideband O2 controller and datalogging system in the world! Zt-2 is about the size of 1" thick business card. Extremely compact design for installation where space is a premium.
IMPORTANT: Warranty does not cover oxygen sensor, as these are wear items. Each oxygen sensor is tested to be fully functional by Zeitronix before shipping.
Zt-2 Specs:
- 0.1 AFR accuracy
- Operating voltage 10V to 18V
- Switching power supply for oxygen sensor heater
- Precise sensor temperature control
- Reverse polarity protection
- Integrated self resettable fuse
- Positive lock connectors
- Protected inputs and outputs
- Flexible Plug and Play Sensor Harness with a small, easy to route through the fire wall, connector
- Wideband Oxygen Sensor included
- Easy to install plug and play kit
- Adjustable Narrowband Switching Point
- Warning Alarms and Triggers
If you want to data log your laptop must have a serial port or a USB to serial port adapter, adapter included!
Inputs/Outputs:
- Bosch Wideband O2 sensor
- Linear Wideband Output AFR=Vx2+9.6
- Serial data output to the Zeitronix Wideband LCD Display
- Serial data output for real time datalogging (PC laptop required)
- RPM Input (tachometer, primary side ignition coil, crank, cam sensor). The RPM input works in any car and any ignition system. No additional adapters needed!
- Simulated and adjustable Narrowband Output to feed a stock ECU
- Throttle Position Input
- Boost (MAP) Sensor Input
- EGT Probe Input
- User Input
- User2 Input, Programmable to view/log 0-5V, Fuel Pressure, Oil Pressure, Boost Pressure, Water Temperature, Intake Air Temperature, Oil Temperature, Transmission Temperature. (Zt-2 model 2010- viewing supported in new LCD, ZR-2 gauges, and logging software)
- Warning Output * 5V output for sensors
ZR-1 Air / Fuel Gauge Specs:
- Black bezel and slim enclosure
- High contrast LED display
- Large 0.4" (10mm) digits - Blue digits
- Slim design for flexible gauge mounting options
- Programmable to start up as an AFR or Lambda gauge
- Peak and Hold feature
- The ZR-1 plugs into the Zt-2 DATA port and can be used while datalogging
- Clean and easy plug and play installation: power and display information is provided using one wire connecting to the Zt-2 DATA port
- The ZR-1 cable length is 5 ft (1.5m)
Mounting Options: The ZR-1 gauge is only 3/4" (19mm) thick. The back of the gauge is completely flat with cable hidden in a cavity and can be surface mounted almost anywhere inside the car cabin using a piece of hook-and-loop mounting tape or double sided tape. The ZR-1 base allows the gauge to be mounted in a standard 2 1/16" (52mm) gauge pod. For additional mounting options the package includes 2 set screws and 2 nuts. ZR-1 gauge dimensions: Base diameter 2" 1/16 (52mm) Bezel diameter 2" 1/2 (62mm) Thickness 0.75" (19mm) Digit height 0.4" (10mm)
We also have the accessories for the Zeitronix Zt-2 available. These are not included, available separately:
- MAP, Boost Sensor, 50 PSI / 3.5 Bar
- EGT Probe with Extension Harness
- Air Intake Temperature Sensor
- Fluid Temperature Sensor
- ZAV-T Alarm & Trigger
- Replacement Bosch Wideband O2 Sensor
- Bungs & Plugs for sensors, different sizes