Zeitronix Zt-3 Wideband Air Fuel Ratio Meter 4.9 Oxygen Sensor AFR O2 CAN Bus
$191.99
In stock
SKU
ZTXZT3CANBUS
Zeitronix Zt-3 Wideband Air Fuel Ratio Meter 4.9 Oxygen Sensor AFR O2 CAN Bus
Zeitronix ZT-3 Wideband Air Fuel Ratio Meter 4.9 Oxygen Sensor AFR O2 CAN Bus
Included in this Zt-3 Kit:
- Zt-3 Wideband CAN Bus Air Fuel Ratio Meter and Datalogging System
- Bosch 5 wire Wideband Oxygen Sensor, Lambda LSU 4.9 series
- Oxygen Sensor Harness (10 feet length)
- Signal Harness
- Serial datalogging cable with RJ-12 to DB-9 converting plug (your laptop must have a serial port or a USB to serial port adapter, not included)
- Instructions
- Display is not included, displays are available separately
Made in the USA! The Zeitronix Wideband Air/Fuel ratio meter and datalogging system is a high quality, stand-alone system for use with carbureted and electronic fuel injection engines. The new Zt-3 has the same high quality, high precision air fuel ratio readings as the Zeitronix signature Zt-2 wideband. The Zt-3 supports wideband air fuel ratio and lambda readings, adjustable simulated narrowband output and a new configurable linear wideband output for ease of use with engine management systems and 3rd party gauges. The new Zt-3's dimensions are only 3 by 2 by 1 inches. The case includes slots case for easy zip tie mounting in a tucked away location.
The Zt-3 CAN supports CAN Bus communication for easy connection and logging through other CAN Bus devices.
- User selectable CAN Bus Speed: 1Mbps, 500 Kbps, 250 Kbps, 125 Kbps
- User selectable CAN Bus ID: Standard (11 bit) and Extended (29 bit)
- User selectable CAN Bus address: 0x0000 to 0x7FFF
- User selectable CAN Bus update rate: 1ms (1000Hz) to 250ms (4 Hz)
- 120 ohm termination - None
- CAN DATA: Data 0, 1 : Lambda 16 bit (Big Endian, Motorola) x 0.001
- Data 2 : Lambda 8 bit x 0.01
- Data 3 : AFR 8 bit x0.1
- Data 7: Lambda sensor status: 0x00 Sensor OK, 0x01 Sensor cold (warm up), 0x02 Sensor too hot, 0x04 Sensor heater circuit open, 0x08 Sensor heater circuit shorted, 0x10 Sensor maxed at rich lambda
- CAN Bus Default Settings: CAN Bus ID Standard (11 bit), CAN Bus ID (HEX) 0x005A, CAN Bus Update Rate 10 ms (100 Hz), CAN Bus Speed 500 Kbps
Works with a stand alone engine management system, a piggy back fuel control or a carbureted engine. Finally you can tune for more power, closer to the edge, precisely monitoring Air/Fuel ratio and datalogging up to 9 hours of data with a blazing rate of 70 samples per seconds per graph.
Very simple installation - connect two wires to +12V and ground and place the O2 sensor in the exhaust stream and you are ready to read AFR! A simple LED indicator displays off, warm-up and running modes.
Very simple installation - connect two wires to +12V and ground and place the O2 sensor in the exhaust stream and you are ready to read AFR! A simple LED indicator displays off, warm-up and running modes.
IMPORTANT: Warranty does not cover oxygen sensor, as these are wear items. Each oxygen sensor is tested to be fully functional by Zeitronix before shipping.
Zt-3 Specs:
- 0.1 AFR accuracy
- Operating voltage 10V to 18V
- Switching power supply for oxygen sensor heater
- Precise sensor temperature control
- Reverse polarity protection
- Integrated self resettable fuse
- Positive lock connectors
- Protected inputs and outputs
- Flexible Plug and Play Sensor Harness with a small, easy to route through the fire wall, connector
- Adjustable Narrowband Switching Point
- Configurable Wideband Analog Output
- Bosch Wideband O2 sensor Input
- Simulated and adjustable Narrowband Output to feed a stock ECU
- Linear Wideband Output (configurable with a default setup of AFR = Volts * 2 + 9.6)
- Serial data output for real time datalogging (laptop or Zeitronix black box required, not included)
- IMPORTANT: Your laptop must have a serial port or a USB to serial port adapter, not included)
Write Your Own Review